[Gems-users] naked checkpoint creation problem

["Zhang Yu" <thuzhangyu@xxxxxxxxx>]

Hi,

I tried to use Gems' workloads script to create a naked checkpoint. I want to get a target machine with solaris express installed. However, when I run the below command:

./naked-check-create.sh 16 65536

After a while, my simulation is stopped. In the target machine's console, I got:

Using RPC Bootparams for network configuration information.
Attempting to configure interface hme0...
-

In simics' console, I got:

[system info] Disabling slave processors.
[system info] Enabling slave processors.
[Turbo] Trampoline found at block start.
[qlc28B_2 info] Undocumented MAILBOX command: 0x5a
[qlc24B_2 info] Undocumented MAILBOX command: 0x5a
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc24B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[qlc28B_2 info] Note: Abort Command Received - Something probably went wrong
[hme0 info] Dropping packet, not connected to network. (Will not warn again)
***  Simics getting shaky, switching to 'safe' mode.
Simics (main thread) received a segmentation fault. Will try to recuperate.
Starting command line. (May have skipped commands in script files.)
simics>

I want to know where did I do wrong. I didn't change the target machine's network configuration, it's:

TARGET_ETHERNET_ADDRESS=10:10:10:10:10:24

TARGET_NI_IP_ADDRESS=10.10.0.11

TARGET_NETMASK=255.255.255.0

TARGET_HOSTNAME=sarek.network.sim

TARGET_ROUTER_IP_ADDRESS=10.10.0.1

Can somebody help me?

Thanks a lot.

Yu