condor_q -better-analyze says
215.000: Run analysis summary. Of 7 machines,
0 are rejected by your job's requirements
7 reject your job because of their own requirements
0 match but are serving users with a better priority in the pool
0 match but reject the job for unknown reasons
0 match but will not currently preempt their existing job
0 are available to run your job
No successful match recorded.
Last failed match: Thu Jun 18 13:32:33 2009
Reason for last match failure: no match found
WARNING: Be advised: Request 215.0 did not match any resource's
constraints
The logs say:
MatchLog:6/18 13:32:33 (fd:7) (pid:4735) Rejected 215.0
group_a.[...]: no match found
NegotiatorLog:6/18 13:32:33 (fd:7) (pid:4735) Request 00215.00000:
NegotiatorLog:6/18 13:32:33 (fd:7) (pid:4735) Rejected 215.0
group_a.[...]: no match found
SchedLog:6/18 13:32:33 (fd:13) (pid:4736) Job 215.0: is runnable
SchedLog:6/18 13:32:33 (fd:13) (pid:4736) Sent job 215.0 (autocluster=0)
SchedLog:6/18 13:32:33 (fd:13) (pid:4736) Job 215.0 rejected: no match found
I still don't know why the job is not running.
Many thanks for helping,
Birol
Matthew Farrellee wrote:
Colak Birol wrote:
Hi,
I am using Condor 7.2.2 on RHEL3. I have computing nodes with 2 dualcore
CPUs, so I configured one dynamic slot with 4 CPUs on each node:
NUM_SLOTS = 1
SLOT_TYPE_1 = cpus=4
NUM_SLOTS_TYPE_1 = 1
SLOT_TYPE_1_PARTITIONABLE = true
When I submit jobs over the SOAP interface, adding following ClassAds to
the Job, it runs fine (the job gets running after some minutes on a
dynamically created slot).
RequestCpus = 1
RequestMemory = ceiling(ImageSize / 1024.000000)
RequestDisk = DiskUsage
But when I say RequestCpus = 2, the job stays idle forever. I assume it
has something to do with the AutoClusterAttrs, which is
AutoClusterAttrs =
"JobUniverse,LastCheckpointPlatform,NumCkpts,RequestCpus,RequestMemory,RequestDisk,Requirements,NiceUser,ConcurrencyLimits"
Anyone has similar problems or a solution?
Best Regards,
Birol
The AutoClusterAttrs shouldn't make a difference.
Does condor_q -better-analyze tell you anything useful?
To get a deeper understanding of why the job is idle you can look at the
StartLog and SchedLog, both should reference the job id.
Best,
matt
_______________________________________________
Condor-users mailing list
To unsubscribe, send a message to condor-users-request@xxxxxxxxxxx with a
subject: Unsubscribe
You can also unsubscribe by visiting
https://lists.cs.wisc.edu/mailman/listinfo/condor-users
The archives can be found at:
https://lists.cs.wisc.edu/archive/condor-users/
_______________________________________________
Condor-users mailing list
To unsubscribe, send a message to
condor-users-request@xxxxxxxxxxx with a
subject: Unsubscribe
You can also unsubscribe by visiting
https://lists.cs.wisc.edu/mailman/listinfo/condor-usersThe archives can be found at:
https://lists.cs.wisc.edu/archive/condor-users/
![[Computer Systems Lab]](https://www-auth.cs.wisc.edu/pics/csl_logo.gif){kind=logo}