Re: [Condor-users] glidein error

[Jaime Frey <jfrey@xxxxxxxxxxx>]

You can edit the config file on the globus resource, then run
condor_glidein with the -runonly parameter (which skips the file setup
phase).

Also, make sure that the globus resource machines don't have private IP
addresses.

 -- Jaime

On Fri, 10 Dec 2004 anayar1@xxxxxxxxxxx wrote:

> What is the easiest way to do it, should I create a local config file with those
> values and ask glidein to use it instead of creating its own? Can I insert these
> values into the glidein condor_config file after the master has started on it?
> Is there a way to restart the master on the globus resource w/o running glidein
> again?
>
> --Arun
>
>
> Quoting Dan Bradley <dan@xxxxxxxxxxxx>:
>
> >
> > You need full inbound and outbound connectivity to the glidein daemons
> > (but significant effort has gone into removing this requirement in the
> > future).  If glidein is running in a private network, then you will need
> > to have a range of ports opened for use by Condor and you will need to
> > configure HIGHPORT and LOWPORT in the glidein condor_config file.
> >
> > --Dan
> >
> > A Nayar wrote:
> >
> > >Schedlog says, unable to connect to the globus resource, so that seems to be
> > >the problem...
> > >
> > >On Thursday 09 December 2004 05:11 pm, Dan Bradley wrote:
> > >
> > >
> > >>Places to look for possible error messages related to this problem:
> > >>
> > >>NegotiatorLog
> > >>SchedLog
> > >>StartLog (of remote execution machine)
> > >>
> > >>--Dan
> > >>
> > >>A Nayar wrote:
> > >>
> > >>
> > >>>Hi,
> > >>>
> > >>> I have managed to get the globus resource to report back to the local
> > >>>pool and now I see the 48 extra vms that I allocated for that resource,
> > >>>now when I try to do a simple helloworld example with requirements to run
> > >>>only on the globus resource the job stays in idle state
> > >>>
> > >>>condor_q gives the following output
> > >>>
> > >>>22.002:  Run analysis summary.  Of 49 machines,
> > >>>     1 are rejected by your job's requirements
> > >>>     0 reject your job because of their own requirements
> > >>>     0 match, but are serving users with a better priority in the pool
> > >>>    48 match, match, but reject the job for unknown reasons
> > >>>     0 match, but will not currently preempt their existing job
> > >>>     0 are available to run your job
> > >>>       Last successful match: Thu Dec  9 14:47:32 2004
> > >>>
> > >>>Why does it match and then not run, I saw lot of posts earlier with this
> > >>>same error but couldnt find a solution in those mails.
> > >>>
> > >>>--Arun
> > >>>
> > >>>
> > >>_______________________________________________
> > >>Condor-users mailing list
> > >>Condor-users@xxxxxxxxxxx
> > >>http://lists.cs.wisc.edu/mailman/listinfo/condor-users
> > >>
> > >>
> > >
> > >
> > >
> >
> > _______________________________________________
> > Condor-users mailing list
> > Condor-users@xxxxxxxxxxx
> > http://lists.cs.wisc.edu/mailman/listinfo/condor-users
> >
>
>
>
>
> ----------------------------------------------------------------
> This message was sent using IMP, the Internet Messaging Program.
>
> _______________________________________________
> Condor-users mailing list
> Condor-users@xxxxxxxxxxx
> http://lists.cs.wisc.edu/mailman/listinfo/condor-users
>

+----------------------------------+---------------------------------+
|            Jaime Frey            |  Public Split on Whether        |
|        jfrey@xxxxxxxxxxx         |  Bush Is a Divider              |
|  http://www.cs.wisc.edu/~jfrey/  |         -- CNN Scrolling Banner |
+----------------------------------+---------------------------------+